EmWeA, Spezialist für optische Bandwaagen


  • Food is about to get safer than ever.

Tilt Switches | Tilt Sensors | Ramsey PROLINE

Tilt Switches (Tilt Sensors) are being hanged up freely and give a signal if deflected from perpendicular line by bulk material. Therefore it will be easy to monitor stock piles, transfer points, filling levels etc.

Our mercury-free tilt switches (tilt sensors) use advanced technology inside the tilt probe to replicate the same performance found in traditional mercurybased tilt switches. A combination of opto-electronics and solid state circuitry inside the probe prevents from jitter and provides stability not found in the typical non-mercury options.

Typical Tilt Switch Applications

Tilt switches / tils sensors used for pile height monitoring.Tilt switches / tilt sensors for belt load monitoring.Tilt switches / tilt sensors for chute monitoring.
Stock pile height
Conveyor belt load
Chute filling

Tilt switches / tilt sensors for low level monitoring.Tilt switches / tilt sensors for high level monitoring.Tilt switches / tilt sensors in hazardous areas.
Low level
High level
Hazardous areas

System Description

Tilt switches (tilt sensors) provide sensing of a 15 degree inclination in a full 360 degrees of direction. Multiple models of the tilt switch (tilt sensor) are available for a wide variety of applications.

Our tilt switches (tilt sensors) have fully encapsulated electronics and come with the necessary mounting hardware. The field-mount control unit includes the traditional green “Normal” and red “Alarm” indicators with LED illuminators (a DIN mount control is also available).

The DPDT relay contacts give you two normally open and two normally closed connections for your external alarms and/or controls. You may select whether “Normal” is the vertical or a tilted position. An adjustable time delay inside the control prevents a momentary tilting of the tilt switch (tilt sensor) from causing a false or premature contact transfer.

The system consists of a control unit and a tilt switch (tilt sensor).

Tilt Switches | Tilt Sensors

We are offering the following tilt switch (tilt sensor) models:

Tilt Switch | Model 20-59-NM

Tilt Switch | Model 20-59-NM

Standard tilt sensor, nickel plated ductile cast iron, 209.3 x 33.3 mm. Width of hanger: 63.5 mm.

Tilt Switch | Model 21-59-NM-ATEX

Tilt Switch | Model 21-59-NM-ATEX

Standard tilt sensor, nickel plated ductile cast iron, 209.3 x 33.3 mm. Width of hanger: 63.5 mm. With ATEX and CSA hazardous area certifications.

Tilt Switch | Model 20-54-NM-SS

Tilt Switch | Model 20-54-NM-SS

Tilt sensor, stainless steel, 260.4 x 25.4 mm.

Tilt Switch | Model 21-54-NM-SS-ATEX

Tilt Switch | Model 21-54-NM-SS-ATEX

Tilt sensor, stainless steel, 260.4 x 25.4 mm. With ATEX and CSA hazardous area certifications.

Tilt Switch | Model 20-55-NM-P

Tilt Switch | Model 20-55-NM-P

Tilt sensor, plastic, light-weighted, 215.2 x 26.7 mm.

Tilt Switch | Model 20-52-NM

Tilt Switch | Model 20-52-NM

Tilt sensor, heavy-weighted, 188.1 x 33.3 mm.

Tilt Switch | Model 21-52-NM-ATEX

Tilt Switch | Model 21-52-NM-ATEX

Tilt sensor, heavy-weighted, 188.1 x 33.3 mm. With ATEX and CSA hazardous area certifications.

Control Units

We are offering the following tilt switch control units:

Control Unit | Model 20-35-NM-DIN

Control Unit | Model 20-35-NM-DIN

DIN mount control (IP20 / NEMA 1).

Control Unit | Model 20-35-NM-F

Control Unit | Model 20-35-NM-F

Field mount control (IP65 / NEMA 4).

Control Unit | Model 20-35-NM-F-4X

Control Unit | Model 20-35-NM-F-4X

Field mount control, stainless steel (IP65 / NEMA 4X).

Control Unit | Model 21-35-NM-F-ATEX

Control Unit | Model 21-35-NM-F-ATEX

Field mount control (IP65 / NEMA 4). With ATEX hazardous area certification.

Control Unit | Model 21-35-NM-F-CSA

Control Unit | Model 21-35-NM-F-CSA

Field mount control (IP65 / NEMA 4). With CSA hazardous area certification.